Trusted Cable Solution Provider - Since 1978

VITALink® Ethernet Fire Resistive Cable

Disclaimer: Images are for reference only. Please check technical specifications for exact conductor counts and layout.

Transit Section VITALINK®-ETHERNET-FIRE-RESISTIVE-CABLE

Application :

Fire & Life Safety

Description:

VITALink® Ethernet Fire Resistive cables are ideal for: • Emergency VoIP communications • IP Area of Refuge communication devices • Addressable Class N fire alarm devices • Critical data communication circuits (VC06)

Construction Cabling:
2-4 Pairs
Construction Conductor:
18 AWG Solid Bare Copper
Construction Drain Wire:
18 AWG Stranded Bare Copper (Shielded constructions only)
Construction Insulation:
Low Smoke, Zero Halogen Thermoset Fire-Roc®
Construction Shield:
Copper Shield (Shielded constructions only)
Construction Tape:
Flame Retardant Tape
Voltage:
600
Temperature:
90ºC
Construction Jacket:
Red Non-Halogen Flame Retardant Polyolefin (Sequential footage markers every 2 feet) Other jacket colors & non-black jacket striping available upon request

Feature 1:
Withstands temperatures up to 1850°F & ensures 2 hour circuit protection
Feature 2:
Meets survivability requirements of NFPA 72 Level 2 and 3
Feature 3:
Listed for use in the United States (free air and conduit) & Canada (in conduit only)
Feature 4:
Sunlight resistant & suitable for use in wet locations
Feature 5:
Solutions for both plenum and riser installations
Feature 6:
No special tools or training required
Feature 7:
No termination kits, brass fittings, or stainless steel straps needed
Feature 8:
Installation requirements are outlined in manufacturer’s instruction guide
Feature 9:
All required hardware components are commercially available off-the-shelf

CSA_Listings:
FAS 105 ST1 FT4 (Shielded constructions only)
CSA Listings:
FAS 105 ST1 FT4 (Shielded constructions only)
UL Listings:
UL Type FPLR-ST1 (Shielded constructions only) and CL3R-ST1 • UL 1424

Performance Standards

ANSI/UL 2196 2 Hour fire rating (See UL Fire Directory R27557) • ULC-S139/2196 Listed with Hose Stream Test for use in FHIT7 System 40A • NFPA 70, 72, 130, and 502 • Meets Cat 3 channel requirements • Transmits data speeds up to 10 Mbps • Sunlight Resistant • For use in Wet Locations • California State Fire Marshal Approved • RoHS Compliant

Core Specifications

Voltage:
600
Temperature:
90ºC

Related Products

ACIC

ACIC (Armored Control and Instrumentation Cable) is rated at 300V and commonly features shielded pairs or triads (e.g., 18 AWG tinned copper conductors). It is designed for reliable signal transmission in electrically noisy environments.

American Connectors - Metal- Clad Cable Connectors

American Connectors - Metal- Clad Cable Connectors

The Connectors are Custom Fit to the Outer Diameter of the Armor. Optional Materials by Request: Stainless Steel, Nickel-Plated Brass

Axle Counter Cable Single & Multi-Quad Transit Cable

Axle Counter Cable Single & Multi-Quad Transit Cable

Axle Counter Cables are designed to support Positive Train Control (PTC) & Communication Based Train Control (CBTC), contributing to the safety of personnel and assets. These devices rely on wired communication to centralized stations that relay information of transit activity. The Axle Counter Device monitors and counts the number of train axles passing by them. The HUB-Link Axle Counter Cable allows installation, with or without direct burial, that provides reliable communication potentially reducing installation cost. (HT06)

HUB-Link® Case Wire Cable

HUB-Link® Case Wire Cable

HUB-Link® Case Wire cables are ideal for the following applications: • Bungalow Electronics Equipment • Trackside Applications • Relay & Signal Apparatus Wiring (HT05)

HUB-Link® LSZH Data Communications Cable

HUB-Link® LSZH Data Communications Cable

HUB-Link® LSZH Data Communications cables are ideal for the following applications: • Transit, Subways, Tunnels • Various Mass Transportation Facilities • Voice and Data (HT02)

HUB-Link® LSZH Telecommunication Cable

HUB-Link® LSZH Telecommunication Cable

HUB-Link® LSZH Telecommunication cables are ideal for the following applications: • Transit, Subways, Tunnels • Various Mass Transportation Facilities • Voice and Data (HT03)

HUB-Link® NYCT Approved Communications Cable

HUB-Link® NYCT Approved Communications Cable

HUB-Link® Transit Communications NYCT Approved cables are ideal for the following applications: • Outside Plant Transit, Subways and Tunnels • Various Mass Transportation Facilities • Voice and Data Telephone Circuits • Installed in Pathways and Termination Closets (HT01)

HUB-Link® Signal Cable

HUB-Link® Signal Cable

HUB-Link® Signal cables are ideal for the following applications: • Transit Control Rooms & Operational Control Centers • Wayside, Tower, and Case • Trackside Signal Equipment (HT04)

NFPA 130 Compliant Patch Cords

NFPA 130 Compliant Patch Cords

NFPA 130 compliant patch cords, using HUB-Link® communications cables, are a plug and play solution that ensures reliable connections between critical equipment in transit systems to help keep passengers safe. Supporting contractors, installers and engineers, these patch cords are pre-assembled and pre-tested to save time and labor during installation. (Patch)

RTX Tunnel Linear - Direct-AC LED Luminaire

RTX Tunnel Linear - Direct-AC LED Luminaire

The RTX is a heavy duty, harsh environment luminaire designed for rail and tunnel applications. Its 1? low-profile design enables RTX to be mounted to the tunnel wall using quick latch hangars or via snake rack and keeps the fixture out of the dynamic envelope. Push-and-click connectors make installation easy to terminate to any wiring box used in today’s tunnel environment. The innovative driverless technology is EMI-silent and connects directly to AC line voltage, providing extreme reliability and zero maintenance.

Order this Product

Cerco Cable Testimonials

What Others Say

Google Reviews

5.0 ★★★★★ (17)